Learn More

 

 

Just about every person may have his or her own opinion with regards to How to Install a Bathtub Yourself.

Setting up a bath tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the project can move quickly; if you need to open up a wall surface to remove the old tub and position the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to take into consideration using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already bought a new tub and do not require to alter the arrangement of your previous water pipelines.
Your tools and material list should consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Preparing for the Installation

To start with, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly problematic because of the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. When the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Making use of both wood boards under its feet, place the bathtub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water and examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill the bathtub as well as likewise check the overflow outlet and also the typical electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has been utilized at the very least when as this will settle it right into its last setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Tub

In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can fracture rather very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I ran across that blog post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the web. Enjoyed reading our posting? Please share it. Let others locate it. Thanks a lot for your time. Come back soon.

Set Up An Appointment